-
- Energy storage hydraulic control system with reliable energy monitoring
- Energy storage high-flow hydraulic forming system
- High-precision digital servo synchronous actuation system
- Energy storage high-flow electro-hydraulic servo test system
- Energy storage, large flow compensation and balance hydraulic control system
- High-frequency fatigue testing system
-
-
- Product
-
Solution
-
Energy storage hydraulic control system with reliable energy monitoring
- Energy storage high-flow power source start-up system
- Energy-saving electro-hydraulic control system
- Hydro-controlled system of electric furnace energy storage device power source
- Emergency control high-pressure accumulator power source for valves
- Governor energy storage power source electro-hydraulic control system
-
Energy storage high-flow hydraulic forming system
-
High-precision digital servo synchronous actuation system
-
Energy storage high-flow electro-hydraulic servo test system
-
Energy storage, large flow compensation and balance hydraulic control system
- High-frequency fatigue testing system
-
Energy storage hydraulic control system with reliable energy monitoring
- Service
- Calculation
Energy-Storage High-Flow Pulse Impact Test System
Published Time:
2024-12-31 08:15
Category:
Solution
High-Flow Electro-Hydraulic Servo Test System with Energy Storage
Energy storage high-flow pulse collision test system
When the test specimen or load requires instantaneous impact energy and demands high‑speed response on the millisecond or even nanosecond timescale, piston accumulators—either with or without an energy‑monitoring system—combined with Sevier high‑flow servo control valve assemblies can serve as the power source for delivering this transient impact energy. Depending on the test objectives or the motion characteristics of the load, the following centralized energy‑supply configurations are typically employed:
- A servo‑proportional valve manifold is employed to distribute the instantaneous flow rate from the accumulator, with control implemented via a PLC system, thereby enabling collision or pulse tests that meet standard test requirements.
- A dedicated Sevier proximity valve manifold is employed, with the energy‑storage power source mounted directly on the manifold. Control is managed via a PLC system, enabling faster local control.
- A gas‑liquid pressure‑boosting piston accumulator is employed, and a local controller mounted on the valve manifold enables nanosecond‑level local control, thereby achieving the experimental objective of delivering greater and faster energy.
Recommended News
SCHWERLL has successfully completed the manufacturing of CNOOC’s super‑flow anti‑recoil valves and the associated super‑flow testing. The products have passed all performance verification tests and flow‑rate assessments, and have obtained certification from CCS, the classification society. Anti-Recoil Valve (AVR), also referred to in the industry as an anti‑backflow valve.
To meet the demands of operating conditions in vehicles, marine vessels, aerospace, and mobile applications—particularly where equipment weight or available installation space is constrained—SCHWERLL began, in 2025, developing miniaturized nitrogen‑boosting units based on its established standard designs. These compact units have been successfully deployed in nitrogen‑boosting systems for marine vessels and heavy‑duty vehicles.
What are the causes of severe pressure drop and shortened service life in bladder-type accumulators?
What are the causes of severe pressure drop and short service life in bladder-type accumulators? The structure of a bladder-type accumulator is quite simple, consisting mainly of an oil chamber surrounding the bladder and a gas chamber equipped with a gas‑tight seal. During operation, the hydraulic fluid must be connected to the hydraulic circuit; when the system pressure rises, the fluid flows into the accumulator, compressing the gas until the pressure in the system pipeline stabilizes.
How can we reduce failures when an accumulator malfunctions?
If an accumulator malfunctions, its performance will be directly affected, potentially leading to abnormal pressures and system failure. Therefore, it should receive close attention during routine operation, and appropriate measures must be implemented to mitigate risks. So, how can we minimize failures when an accumulator malfunctions? The following sections address this issue.
Accumulators are intriguing components in hydraulic systems, analogous to capacitors in electrical circuits or springs in mechanical systems. As critical energy‑storage elements, they serve a variety of sophisticated functions, including hybrid‑power applications, shock absorption, pressure stabilization (and sometimes flow‑rate regulation), and the rapid release of stored energy to simulate impacts.
Is a bladder-type accumulator suitable for use in series with gas cylinders or cylinder banks?
1. Bladders typically have a shorter service life than piston‑type accumulators, and their quality varies significantly among different manufacturers. 2. Many factors can shorten a bladder’s lifespan and lead to rupture, including variations in the bladder’s intrinsic quality and durability; improper handling during assembly (e.g., failure to pre‑fill with fluid for lubrication); incorrect procedures during pre‑charging (e.g., insufficiently slow inflation); errors in calculating the pre‑charge pressure; oil‑port flow velocities approaching or exceeding 7 m/s; single‑stroke reciprocation times of 10 seconds or less when used for energy storage; collisions between the bladder and check valves during operation; large temperature fluctuations (including significant seasonal differences); prolonged lateral vibration; fluid‑induced corrosion; and inertial impacts from minute solid contaminants in the working medium, among others.
Products of Different Specifications
Products
Application Fields
Application
Partners
Partner
Exporting Countries and Regions
Exported Countries
Schwerll Fluid Control (Beijing) Co., Ltd.
Email: schwerlltec@schwerll.com.cn
Address: Building 39B, Floor 1, No. 16, Huanke Zhong Road, Tongzhou Park, Zhongguancun Science and Technology Park, Tongzhou District, Beijing
Welcome to access our company through the following methods
Copyright © 2024 Schwell Energy Storage Technology (Beijing) Co., Ltd.